LR Defender 110 & Series LWB Station Wagon 2nd Row Upstand and Floor

Category: Uncategorised

£173.00-£224.50

1 x Floor End Caps (next to C post)

These floor end caps fit all Defender & Series 4 or 5 door Supplied in 2mm thick aluminium and with a protective film To view workshop, click here

Option
1001
1002	Clear

£6.00

1 x 2nd Row Footwell to Rear Floor Extended Upstand

The Land Rover Defender 110/Station Wagon & Series LWB 2nd Row Footwell Up-stand. Runs the full width between the 2 C posts. Made out of 2mm thick aluminium and are machine cut and CNC pressed for accuracy. Shorter version can be bought, please see YRM114A To view workshop, click here

A Rivets
B Rivets	Clear

£43.00

1 x Underfloor Support 2mm Aluminium

Brand new Defender 110/Station Wagon Series LWB Underfloor Support made from 2mm Aluminium. This part bolts between the 2 C Post Land Rover Manufacturers part no. ATF710090 YRM version You can also buy the galvanised version, please see YRM117B To view workshop, click here

A Rivets
B Rivets	Clear

£29.00

1 x 2nd Row Floor 2mm Thick Mill Finish - LR Defender 110 & Station Wagon & Series

Land Rover Defender 110 County Station Wagon & Series LWB Station Wagon 2nd Row Floor. Comes with strengthen bar structurally adhesively applied Supplied in 2mm thick aluminium and with a protective film They are also machine cut and CNC pressed for accuracy To view workshop, click here

YRM1042

Clear

£95.00

1no.	108	Land Rover Defender 110 & Series LWB Floor End Caps (next to C post)
1no.	114B	Land Rover Defender 110/Station Wagon Series LWB 2nd Row Footwell to Rear Floor Upstand
1no.	117A	Land Rover Defender 110/Station Wagon Underfloor Support Aluminium
1no.	129	Land Rover Defender 110/Station Wagon & Series 2nd Row Floor
	1001	Type A Rivets Grip Range 1.6mm – 6.2mm Pk 100
	1002	Type B Rivets Grip Range 4.8mm – 11mm Pk 100

Tools used

Selection of spanners and sockets set
Riveter
Drill and various drill bits
Jigsaw
Tape measure and Marker
Bolster and Hammer
Appropriate PPE ,Goggles, Gloves, Boots

Steps

1	The 2^nd row floor and upstand removed, mark a line between the front of the 2 rear wheel arches and cut along with jigsaw, if you wish to replace the full rear floor with YRM 114B you will require YRM 115C which is shorter than stand floor to allow for upstand coming onto floor further.
2	Offer the underfloor support in place as you can see it has been notched around the underfloor supports (YRM product ref 098).
3	Clamp the underfloor support in place ensuring the holes on the underfloor support line up with those on the C post angle (YRM product ref 074 & 075), then drill and rivet between the wheel arch to hold under floor support in place. Apply PVC tape between dissimilar metals.
4	Slide the 2^nd row upstand in place as shown in photo, this is pre-cut and will slide then offer up to the front of the rear wheel arch. Apply PVC tape between dissimilar metals, then rivet in place along the underfloor support and wheel arch.
5	The LWB floor end caps go along the top of the upstand and underneath the C post angle as shown in photo this will need to be match drilled and riveted.
6	When fitting the 2^nd row floor apply PVC tape to along sill rail (YRM product ref 070 & 071) and anywhere dissimilar metals touch and fix in place